0

Спасибо: |
Получено: 0 Отправлено: 0 |
Всем привет! Приобрел VW B-5+ variant, двигатель AKN 2,5 V-6, TDI, 4motion. Устраевает полностью пригнан из Германии. Единнственный минус не работает навигация в России и нет CD-ченейджера.
Подскажите как снять правильно штатную RNS MFD ни чего несломав, и как вывести USB и AUX? зарание благодарю!
Спасибо: |
Получено: 0 Отправлено: 1 |
ALEKS_021
Привет, Отличная авто!Завидую вашим пошлинам...
для снятия RNS нужно 4 специальных ключика.
Если поискать по форуму, то можно найти картинку как они выглядят...
http://www.passatworld.ru/phpBB2/topic33562.html
Спасибо: |
Получено: 0 Отправлено: 3 |
вэлкам
Спасибо: |
Получено: 8 Отправлено: 0 |
набери в поиске xcarlink. Рекомендую!
VW PASSAT В5+ TDI 1.9 AVF, EYF 131л.с. Универсал 2005г ->Ford Mondeo 2009 седан 2.0-> Skoda Superb Combi TDI 2013
Спасибо: |
Получено: 0 Отправлено: 0 |
Просмотрел информацию по снятию штатной башки но там ничего не нашел по своей модели башки. У меня большой монитор и клима стоит внизу![]()
Спасибо: |
Получено: 167 Отправлено: 181 |
ALEKS_021
Шалом!!!
Skoda octavia 2.0TDI 6DSG
ИмелSKODA SUPERB COMBI 2.0 TDI 6DSG Elegans+ passat B3 и B5
Спасибо: |
Получено: 2 Отправлено: 14 |
ALEKS_021 добро пожаловать, в полку 2,5 прибыло!
ну как нравится?
ALEKS_021 брал осознано?
Спасибо: |
Получено: 0 Отправлено: 1 |
Какая разница! У башки 4 щели, в которые вставляются 4 стандартных ключа...Сообщение от ALEKS_021
Просмотрел информацию по снятию штатной башки но там ничего не нашел по своей модели башки. У меня большой монитор и клима стоит внизу
Тут почитай для начала http://vwnavi.com/forums/forumdisplay.php?f=59
Спасибо: |
Получено: 20 Отправлено: 11 |
привет![]()
B6 2.0TDI, BMR , BMW e39
Спасибо: |
Получено: 1 Отправлено: 7 |
ALEKS_021
Привет!
Вливайся!!!
Jetta V 2007 МКПП 1.6 BSE
Passat B6 2009 МКПП 1.6 BSE продан
Спасибо: |
Получено: 4 Отправлено: 1 |
Привет! Присоединяйся!![]()
Спасибо: |
Получено: 0 Отправлено: 0 |
Привет! Вся разница в том что на этой башке всё очень плотно и в какие щели совать эти ключи![]()
Спасибо: |
Получено: 2 Отправлено: 14 |
ALEKS_021 не мучайся!
Добавлено спустя 36 секунд:
Radio navigation system (RNS) with multi-functional display
Removing and installing radio/navigation unit
Notes:
◆ The part number for the complete Radio navigation system is printed on a sticker on the radio/navigation system housing!
◆ If an RNS unit from a vehicle is fitted into a different vehicle, it is essential that the part number of the replacement unit is the same as the unit previously installed. Otherwise faults will occur with the navigation as the turn angle sensor adjustment in the RNS unit will not be compatible for the vehicle.
◆ If the RNS unit is replaced by a new part or exchange part the replacement unit is coded ex factory with the setting "with control unit for traffic information". If the vehicle has no traffic information control unit, the fault "00481" is set on these vehicles. Therefore, code the navigation system to "without control unit for traffic information" =>Adapting components, navigation system => page 91-275.
◆ If the RNS unit is replaced by a new part or exchange part, adapt the impulse rate of the ABS wheel speed sensors and the tyre circumference to improve accuracy of the system. Adapting components, navigation system => page 91-275.
Special tools, testers, measuring instruments and auxiliary items required
◆ T10057 Release tool
To remove the radio/navigation system, 2 sets of release tool T10057 are required.
Removing:
Note:
Before removing the radio/navigation system obtain the radio code from the customer. If the radio/navigation system is renewed, always activate the anti-theft coding (see Instruction Manual). The customer must be informed of the new code.
◆ If the radio/navigation system has a TV function, carefully pull out the device to avoid damaging the RGB connection. If the RGB connection is damaged, the wiring connection must be renewed all the way to the TV tuner. Repair of the RGB connector is not possible.
Carry out work sequence as follows:
‒ → Slide radio release tool T10057 into the release slots -arrows- as shown until they locate.
Top L - top and bottom on left
Top R - top and bottom on right
‒ Pull radio/navigation system out of the dash panel using the grip rings of the release tools.
‒ Release connections and pull off
Pulling out release tools:
‒ → Press locking tabs -arrow- and pull release tool out forwards.
Installing:
‒ Connect plug to radio/navigation system.
‒ Slide radio/navigation system straight into the dash panel, until it engages in the assembly frame.
Note:
Never press on display or the operating unit when fitting the radio/navigation system unit, otherwise they may be damaged.
◆ If the radio/navigation system is renewed, the proper broadcasting standard must be set for television reception.
=> Operating instructions, radio/navigation system/TV tuner
‒ Check the radio navigation system code and recode as necessary.
‒ Coding radio system in radio/navigation system => Adapting components, radio => Page 91-33.
‒ Coding navigation system in radio/navigation system => Adapting components, navigation system => Page 91-275.
Добавлено спустя 37 секунд:
вот еще
Добавлено спустя 38 секунд:
и еще
Спасибо: |
Получено: 5 Отправлено: 13 |
ALEKS_021
Привет!